setrbrothers.blogg.se - Switcher cast says screen duplicator cannot create output

When you troubleshoot multicast routing, the primary concern is the source address. This document is not restricted to specific software and hardware versions. There are no specific requirements for this document. Under Live, go to Select Output Monitor and select Secondary Monitor from the drop down list.This document describes common problems and solutions for IP multicast.The Secondary Device should be set to Monitor.The Primary Device should be set to Notebook or Built-in-Display.Under Devices or Display Devices, click on the Extended Desktop option.

In the section titled Live Options, click the Output Monitor dropdown and select Secondary Monitor.

The instructions below will walk you through the process. However, you may need to set up the output screen manually. Setting Up EasyWorship To Use Your Second MonitorĮasyWorship will normally find the secondary display and automatically send the output to that screen. To do this, follow the instructions below.

Now you need to set up EasyWorship to use your second monitor.

If prompted to keep the settings click Yes.

Verify the color setting for monitor number 2 is set to 32 bit.

(The recommended setting is typically the best to try first.)

Select the Extend my Windows desktop onto this monitor or select Extend these displays from the drop down list.

(If display 1 and 2 boxes do not appear, your computer does not have dual monitor capability, or you do not have a projector or monitor plugged into the secondary video output on the computer.)

EasyWorship will open the Screen Resolution dialog box.

In the section titled Live Options, click the Monitor Setup button.

Click OK.īack to Top Enable Windows Extended Desktop In the Live settings, Select Monitor 2 (Secondary) for the Output monitor. The secondary monitor is not selected as the output monitor in EasyWorship.Ĭlick the Edit menu, then Options. Windows extended desktop is enabled, but EasyWorship still displays the output on my primary monitor. Connect your projector or secondary monitor to the secondary monitor port on your graphics card and make sure that the monitor, or projector, is turned on. Use the instructions in Intel Graphics Monitor Setup to enable the windows extended desktop for your Intel Graphics card. You have an Intel Graphics card, or you do not have your projector connected to your secondary video port, or the projector is not turned on. I enabled the Windows extended desktop, but it disables itself after I apply the setting. See below: Enabling Windows Extended Desktop. Your windows desktop has not been extended to the second monitor.Įnable the windows extended desktop. If your problem cannot be resolved by following the steps below, contact our Customer Support Team via email at see the same thing on my second monitor as I see on my primary monitor.

NOTES: See Enabling Windows Extended Desktop for instructions on how to check a computer for Dual Monitor compatibility and for instructions on setting up Dual Monitors to use with EasyWorship. This would allow you to have two secondary outputs (live screens) or a second monitor on the desk as well as a secondary output for the audience. You may also add a video splitter to the secondary output.Customers using laptops will use their laptop monitor as the control monitor (Monitor #1) and the output on the side or back of the laptop for output to the audience (Monitor #2).EasyWorship may be set up with a single monitor on the desk to control the software (Monitor #1) and with a projector as the secondary output (Monitor #2).A laptop with a video output (VGA, DVI or HDMI) on the side or back of the laptop.Ĭommon ways to set up a computer for dual monitor output.Two video cards with a single output on each card.Video Card Configurations for Windows Extended Desktop The following are three different video card configurations that will allow you to use Windows Extended desktop: This kind of "Dual Monitor Display" makes it possible for an operator to be editing the Schedule Area in EasyWorship while the congregation is viewing only the current song, scripture, video, presentation, or feed.ĮasyWorship uses Windows extended desktop to accomplish this. The second display-Monitor #2 or the secondary monitor-goes to the output screen that is projected to the congregation (this could be a TV, projector, or LCD screen). The first display-Monitor #1 or the primary monitor-goes to the control screen, which is what the operator sees. That means it can produce two different displays at the same time. Setting Up EasyWorship to Use Your Second MonitorĮasyWorship is designed for dual monitor display.Video Card Configurations for Windows Extended Desktop.Support 6 Home Knowledge Base Troubleshooting V6 Getting Started Dual Monitor Setup